737 Measurement Reference ID Code

Code identifying the broad category to which a measurement applies

Type
Identifier (ID)
Length
Min 2 / Max 2
Codes
CodeDescription
9LNinth Layer
AAMeter reading-beginning actual/ending actual
ABAverage Balance
ACMaximum Balance
AEMeter reading-beginning actual/ending estimated
AFActual Total
AGCompliance Total
AHGross Compliance Total
AINet Compliance Total
AJEffectiveness
AKPenetration
AMCapacity
ANWork
AOAccount Opened Period
APApartments
AQAmount Owes
ARAnnual Result
AVAverage Reading
BABase Point
BBBank Balance
BCBilled Actual
BDBilled Dimensions
BLBundle Limitation
BMBase Metal
Original or base product to which coatings are to be applied
BNBilled Minimum
BOMeter Reading as Billed
Used when billing charges are based on contractual agreements or pre-established usage and not on actual usage
BPBearing Piece Limitation
BRBilled History
BTBatch Limits
Limits set on test results from all product made for one unit or period of production
BZBatten Size
C1Conformance Property Status
CACoating
Material or product added to another product (base metal) to enhance its characteristics
CBCondominium
CCCooperative
CFConversion Factor
CGAverage Owing
CHChemistry
CJCurrent Balance
CKDiscounted Checks
CLDrafts
CMCommercial
CNCore Notch Dimensions
COConcentration
CPLetter of Credit Size
CQPayment Orders
CSCore Size
CTCounts
CUPledge Size
CVCumulative Test Period
The total period during which a series of tests are conducted
CWPromissory Notes in Force
CYSecured Amount
DEDefects
DNDunnage Dimension
DTDimensional Tolerance
EAMeter reading-beginning estimated/ending actual
EEMeter reading-beginning estimated/ending estimated
EFEvaluation Factors
ELElectrical Characteristics
ENEnvironmental Conditions
The data values to be reported reflect the environmental conditions surrounding a situation including but not limited to test environments
FCFirst of Campaign Result
FDFinished Dimensions
Dimensions of the final or end-use product
FHRadio Operations
FJAntenna Characteristics
FVFiring Values
FZFile Size
GCContractor Delivery Limitations
GLGuidelines
GOGovernment Ordering Limitations
GPOrdering Period Limitations
HCHigh Credit Average
HRHistorical Result
IDIndustrial
INIncrustation
IRInterpolated Result
A test result value calculated by interpolation between two physical tests
LCLimited Weight/Size Coils
LDLoad Planning Dimensions
LGLoans Granted
LLLift Limitation
LMLayer of Multiple Layered Product
LPLast Sold Period
LSLot Status
LTLot Limits
Limits set on test results from all product contained in a single shipment (which may involve any multiple or fraction of transportation carrier units) to one customer
MPMaturity Period
MRBase Material Result
NCNet Change
NENeighborhood
NXNet Explosive Weight
ODOrdered Dimensions
OGOriginal
OLOrder Limits
OPOther Property
P1Platform Limitation
PAPallet Dimensions
PBReceivership Period
PCParting Cut (Sawcut)
PDPhysical Dimensions
PIProject Incomplete
PJProject Complete
PKPackage Dimensions
PLPackage Limitations
PMPermitted
The condition or activity approved by the appropriate regulatory agency
POPosition
PRProduct Dimension Range Price Bracket
PSProduct Characteristic Specification
PTPretest Period
The nominal period that a tested device is preconditioned
PUPlanned Urban Development
PYProperty
QRQuarterly Result
QVQuantity Variation
R1Opening Reading
R2Closing Reading
RAReject Amount
RGRegulatory Limit
RLReceiving Facility Limitations
RNLengths Limitation
RORoll Limits
Limits set on test results from one roll of product shipped to a customer
RPRelative Position
RQRequested
The condition or activity submitted for approval by the appropriate regulatory agency
RSResponse Time
RTReplacement
SASpacing/Margin
SBSingle Family
SCStandard Industrial Classification (SIC) Code Size Standards
SDShipped Dimensions
SEProperty Specifications
Indicates that the data to follow are target specifications
SFShelf Life
SHShipping Tolerance
SJSubject Phase
SKSkid Dimensions
SLSkid Limitations
SMShade
SPSplices
SRSurface Roughness
STSurface Treatment
SUSurface
SZSubject Property
TATwo to Four Family
TDSplice Tape Dimensions
TETemperature
TITime
TLTransportation Equipment Limitations
TOTotal Dimensions
TPTest Period
The nominal period that a test is conducted
TRTest Results
Indicates that the data to follow are the results test measurements
TSSingle Test Limits
Limits set on each measurement of the specified product characteristic or manufacturing process so that any single test whose value falls outside these limits causes the product or process to be declared out-of-specification
TTThis Type Property
VTVacant
WAWaste Amount
WRWarranty
WTWeights
ZAMulti - Family
ZPLog Zero Point of Reference
The physical location on the well, measured above or below the ground surface, from which the wireline well log measurements, such as the kelly bushing and casing head flange, are adjusted

Stedi is a registered trademark of Stedi, Inc. Stedi's EDI Reference is provided for marketing purposes and is free of charge. All names, logos, and brands of third parties listed on our site are trademarks of their respective owners (including “X12”, which is a trademark of X12 Incorporated). Stedi, Inc. and its products and services are not endorsed by, sponsored by, or affiliated with these third parties. Our use of these names, logos, and brands is for identification purposes only, and does not imply any such endorsement, sponsorship, or affiliation.